Setting up Samba as a Print Server
A print server accepts print jobs from network computers, queues them locally and send them to the appropriate printers. Beside domain and file service capabilities, Samba can act as a MS Windows compatible print server as well. While Samba provides the interface to Windows/SMB machines, CUPS or LDP is used by Samba to send print jobs to the devices.
In the following, we give an overview about Sambas supported backends, including how to add new network printer to them. The examples setup a RAW printer (content is send unmodified to the device). We don't use filters or drivers on the backend, because a RAW printer allows the rendering of the output to be done on the workstation by the printer vendors specific driver. In the latter the printer will be shared by Samba to provide the service to the network. If you're also interested in automatic printer driver deployment via Point'n'Print, see the corresponding documentation.
Print server backends
In the following we assume, that the print server backend is already basically configured, running and printers can be added.
CUPS is currently the most widely used spool system in *nix environments and shipped with most distributions. Samba has built-in support and defaults to CUPS, if the development package (header files and libraries) are found at compile time.
- Open the CUPS admin web frontend (https://servername:631/admin)
- Click "Add Printer" on the "Administration" tab
- Choose the way that your printer is connected and enter the appropriate URL. Examples:
- LPD protocol:
- Internet Printing Protocol
- Forwarding the jobs to a Windows print server (Note: Vista and higher don't allow anonymous connects by default. You have to provide a username and password for the connection)
- Enter a name for the printer
- Choose "Raw" for the printer vendor and model
- Save the the settings
This was the first widely used printing system and is still used on many servers. It is very simple to install and to configure. There are different implementations of LPD servers, like the often used LPRng.
- Add the following line to your "printcap" file (typically located in /etc/)
- For the used options in above example check out the printcap man page.
- Create the printers spool directory
# checkpc -f
- Restart LPD
# service lpd restart
- The following command allows you query the state of the printer:
# lpq -P PRINTERNAME Printer: PRINTERNAME@SAMPRINTSERVER (dest PRINTERNAME@IP_or_DNS_Name) Queue: no printable jobs in queue Ready no entries
Configure Samba as print server
Enable spoolssd (optional)
Note: Some features of spoolssd were broken before 4.0.17 and 4.1.7. If you consider using spoolssd, please use a later version!
spoolssd, a feature introduced in Samba 4.0, increases printer performance. In the past, when a print job came in, a smbd child process was forked, to initialize the printcap cache, spoolss, etc. If you have a huge printcap cache and it needs to be updated first, the client could hang for several seconds. Since Samba 4.0, you can configure spoolssd to be started as forked processes. If enabled, you'll see additional smbd processes, which will handle only spoolss requests. The master process is a simple daemon with a small memory footprint, that only forks and kills childrens serving the spoolss pipe. When a connection comes in, it can directly start to talk to the daemon and ask for information about the printer without any delay, this gives a performance improvement.
To enable spoolssd, add the following to the [global] section of your smb.conf:
rpc_server:spoolss = external rpc_daemon:spoolssd = fork
After the next restart of Samba, you will discover additional smbd processes that handle spoolss requests:
With spoolssd enabled: With spoolssd disabled (default): 30903 smbd 30903 smbd 30912 \_ smbd 30912 \_ smbd 30913 \_ smbd 30914 \_ smbd 30915 \_ smbd 30916 \_ smbd 30917 \_ smbd 30918 \_ smbd 30920 \_ smbd 30921 \_ smbd 30922 \_ smbd 30923 \_ smbd 30924 \_ smbd
You can adjust the daemons behaviour through the following parameters (the values in the examples are the defaults):
spoolssd:prefork_min_children = 5 # Minimum number of child processes spoolssd:prefork_max_children = 25 # Maximum number of child processes spoolssd:prefork_spawn_rate = 5 # Start (fork) x new children if one connection comes in (up to prefork_max_children) spoolssd:prefork_max_allowed_clients = 100 # Number of clients, a child process should be responsible for spoolssd:prefork_child_min_life = 60 # Minimum lifetime of a child process (60 seconds # is the minimum, even a lower value has been configured)
spoolssd is still a new feature. If you encounter any bug, please report it at https://bugzilla.samba.org/, to get it fixed as soon as possible.
This share defines general information about your printing backend. See the "[printers]" section in the smb.conf man page for further information.
- Add the [printers] section to your smb.conf
[printers] path = /var/spool/samba/ printable = yes printing = CUPS|LPRNG|...
- Check for Samba CUPS support (only necessary, if "printing = CUPS")
# smbd -b | grep CUPS HAVE_CUPS_CUPS_H HAVE_CUPS_LANGUAGE_H HAVE_CUPS HAVE_LIBCUPS
- If you don't get any output, make sure that the CUPS header files and libraries are installed and recompile Samba with --with-cups
- Create the Samba spool directory, defined in the "[printer]" share.
# mkdir -p /var/spool/samba/ # chmod 1777 /var/spool/samba/
Unless "load printers = yes" was set in your smb.conf to automatically share all printers available in the backend, for each printer, that should be shared by Samba, a separate share is required:
[MyDemoPrinter] path = /var/spool/samba/ browseable = yes printable = yes printer name = Printername_in_backend # Set the "printer name" parameter to the name of your # corresponding CUPS/LPD/... queue name
Reload Samba after configuration changes:
# smbcontrol all reload-config