Samba Port Usage: Difference between revisions

From SambaWiki
m (Fix typo)
m (Mmuehlfeld moved page Samba port usage to Samba Port Usage without leaving a redirect: Used TitleCase in the title)
 
(9 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Depending on the installation mode, Samba opens different ports. For details, see:
= Introduction =


* [[Samba AD DC Port Usage]]
If you require to secure your Samba installation with a firewall, you would need information, what ports and protocols are used. This page will give you an overview.


* [[Samba NT4 PDC Port Usage]]


* [[Samba Domain Member Port Usage]]



= Identify on which ports and interfaces Samba is listening =

You can use "netstat" to identify which ports Samba and related daemons are listening on and on which IPs:

# netstat -tulpn | egrep "samba|smbd|nmbd|winbind"

The following is a snippet of an example output:

tcp 0 0 127.0.0.1:139 0.0.0.0:* LISTEN 43270/smbd
tcp 0 0 10.0.0.1:139 0.0.0.0:* LISTEN 43270/smbd
tcp 0 0 10.0.0.1:88 0.0.0.0:* LISTEN 43273/samba
tcp 0 0 127.0.0.1:88 0.0.0.0:* LISTEN 43273/samba
tcp 0 0 127.0.0.1:445 0.0.0.0:* LISTEN 43270/smbd
tcp 0 0 10.0.0.1:445 0.0.0.0:* LISTEN 43270/smbd
.....

The above example shows, that the services are listening on localhost (127.0.0.1) and the interface with IP 10.0.0.1 - each on the listed ports (139, 88, 445,...).





= Port usage when Samba runs as DC =

{| border="1"
!Service
!Port
!protocol
|-
|DNS
|53
|tcp/udp
|-
|Kerberos
|88
|tcp/udp
|-
|End Point Mapper (DCE/RPC Locator Service)
|135
|tcp
|-
|NetBIOS Name Service
|137
|udp
|-
|NetBIOS Datagram
|138
|udp
|-
|NetBIOS Session
|139
|tcp
|-
|LDAP
|389
|tcp/udp
|-
|SMB over TCP
|445
|tcp
|-
|Kerberos kpasswd
|464
|tcp/udp
|-
|LDAPS ''(only if "tls enabled = yes")''
|636
|tcp
|-
|Dynamic RPC Ports*
|1024-5000
|tcp
|-
|Global Cataloge
|3268
|tcp
|-
|Global Cataloge SSL ''(only if "tls enabled = yes")''
|3269
|tcp
|-
|Multicast DNS
|5353
|tcp/udp
|}

<nowiki>*</nowiki> Samba, like Windows, supports dynamic RPC services. The range starts at 1024. If something occupies this port for some reason, it will be a different port (literally walked up from 1024).

'''Remember, that there can be other ports too, which are related to your Samba installation but not provided from Samba itself, like if you run a NTP server for time synchronisation as well.'''





= Port usage when Samba runs as NT4-domain =

{| border="1"
!Service
!Port
!protocol
|-
|End Point Mapper (DCE/RPC Locator Service)
|135
|tcp
|-
|NetBIOS Name Service
|137
|udp
|-
|NetBIOS Datagram
|138
|udp
|-
|NetBIOS Session
|139
|tcp
|-
|SMB over TCP
|445
|tcp
|}





= Prevent Samba from listening on all interfaces =

Sometimes you don't want Samba to listen on all interfaces of your host. For example, when the host is directly connected to the internet, you surely don't want to provide your shares to the rest of the world. If you limit Samba to listen only on the internal NIC(s), you don't need a firewall to prevent access from the outside.

Add the following to the "[global]" section of your smb.conf to bind Samba to eth0 and loopback:

bind interfaces only = yes
interfaces = lo eth0

The "interfaces" parameter allows various ways to restrict. See the manpage for more details.

After the changes, restart Samba.

Latest revision as of 10:54, 6 September 2017

Depending on the installation mode, Samba opens different ports. For details, see: