Bidirectional Rsync/Unison based SysVol replication workaround: Difference between revisions
m (Mailing URL change.) |
Mmuehlfeld (talk | contribs) m (Added categoy.) |
||
(9 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
= Introduction = |
= Introduction = |
||
Samba AD currently doesn't provide support for SysVol replication. To achive this important feature in a Multi-DC environment, until it's implemented, workarounds are necessary to keep it in sync. This HowTo provides a basic workaround solution based on |
Samba AD currently doesn't provide support for SysVol replication. To achive this important feature in a Multi-DC environment, until it's implemented, workarounds are necessary to keep it in sync. This HowTo provides a basic workaround solution based on rsync and unison. |
||
= Information on |
= Information on unison + rsync replication = |
||
This HowTo describes a solution for SysVol replication, that is based on |
This HowTo describes a solution for SysVol replication, that is based on rsync and unison. As Compare to the rsync method, it is bidirectional. But this howto only cover two DC setup. |
||
It have the following advantages: |
It have the following advantages: |
||
* setup is fast |
* setup is fast done |
||
* configuration is very easy |
* configuration is very easy |
||
* Can work with windows ( |
* Can work with windows (Please add in) |
||
We will use rsync through a SSH tunnel. |
|||
= Setup the SysVol replication = |
= Setup the SysVol replication = |
||
Some assumptions: |
|||
== Installation == |
|||
You are running all commands as root. |
|||
rsync is located /usr/bin/rsync |
|||
sysvol is located /var/lib/samba/sysvol on both DC1 and DC2 |
|||
unison is located /usr/bin/unison |
|||
DC1 is at DC1 |
|||
DC2 is at DC2 |
|||
sysvolsync log is located /var/log/sysvol-sync.log |
|||
Change the path if that don't fit your setup. |
|||
I don't see any package but osync available on |
|||
[https://github.com/deajan/osync]https://github.com/deajan/osync |
|||
== Getting Osync == |
|||
At the time of writing this Osync is still at v.100pre. |
|||
However, you should always get a stable branch when it is available. |
|||
We are getting it done using master branch. |
|||
wget https://raw.githubusercontent.com/deajan/osync/master/osync.sh |
|||
chmod +x osync.sh |
|||
Move osync to /usr/bin/ or your preferred dir |
|||
mv osync.sh /usr/bin/ |
|||
== Getting Osync Configuration == |
|||
wget https://raw.githubusercontent.com/deajan/osync/master/sync.conf |
|||
Move it to /etc/osync/ |
|||
mkdir /etc/osync/ |
|||
mv sync.conf /etc/osync/sync.conf |
|||
=== Setup on the Domain Controller with the PDC Emulator FSMO role === |
=== Setup on the Domain Controller with the PDC Emulator FSMO role === |
||
Some assumption: |
|||
* You are running all command as root. |
|||
* rsync is located /usr/bin/rsync |
|||
* sysvol is located /var/lib/samba/sysvol on both DC1 and DC2 |
|||
* osync is located /usr/bin/osync |
|||
* osync.conf is located /etc/osync/sync.conf |
|||
* DC1 is at DC1 |
|||
* DC2 is at DC2 (And already join DC1) |
|||
* sysvolsync log is located /var/log/osync_*.log |
|||
* rsync must support extended ACLs |
|||
* Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs! |
* Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs! |
||
* sysvol must be on disk which is mounted to support acl and also xattr |
|||
* We don't need to setup rsync server. |
* We don't need to setup rsync server. |
||
* Install unison by using your package manager or compile from source. (Gentoo need to do <tt>eselect unison</tt> to create the link) |
|||
Change the path if that don't fit your setup. |
|||
==== Creating SSH Public Key and ssh-copy to DC2==== |
==== Creating SSH Public Key and ssh-copy to DC2==== |
||
ssh-keygen -t |
ssh-keygen -t rsa |
||
ssh-copy-id -i ~/.ssh/ |
ssh-copy-id -i ~/.ssh/id_rsa.pub root@DC2 |
||
You can try to access DC2 via ssh |
You can try to access DC2 via ssh |
||
ssh DC2 |
ssh DC2 |
||
=== |
==== Setup ssh Control ==== |
||
If the remote system enforces rate limits on incoming ssh connections, unison wil fail if you try to run it this way. |
|||
Edit the /etc/osync/sync.conf and make some changes |
|||
So we create the first ssh connection as a controlpath file in the location specified, all subsequent connections will reuse on the first connection. |
|||
mkdir ~/.ssh/ctl |
|||
#!/usr/bin/env bash |
|||
cat << EOF > ~/.ssh/ctl/config |
|||
SYNC_ID="sysvol_sync" |
|||
Host * |
|||
MASTER_SYNC_DIR="/var/lib/samba/sysvol" |
|||
ControlMaster auto |
|||
SLAVE_SYNC_DIR="ssh://root@DC2:22//var/lib/samba/sysvol" |
|||
ControlPath ~/.ssh/ctl/%h_%p_%r |
|||
SSH_RSA_PRIVATE_KEY="/root/.ssh/id_rsa" |
|||
ControlPersist 1 |
|||
PRESERVE_ACL=yes |
|||
EOF |
|||
PRESERVE_XATTR=yes |
|||
SOFT_DELETE=no |
|||
DESTINATION_MAILS="your@email.com" |
|||
==== Setup Sysvolsync Log files ==== |
|||
I'm having some soft_delete bugs with Osync as files/folder conflict when move the deleted folder. |
|||
Do the following on DC1 so that we can check what happen on the sync. |
|||
(Checking with the developer, might get fix soon) |
|||
Please include this files into to log rotate as we didn't control the log size here. |
|||
So Before that "SOFT_DELETE=no" |
|||
touch /var/log/sysvol-sync.log |
|||
Osync have one benefit as it will only send email alert if there is problem. |
|||
chmod 640 /var/log/sysvol-sync.log |
|||
=== Setup |
==== Setup Unison defaults running parameters ==== |
||
Please run the following on DC1 |
|||
* On DC2 Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs! |
|||
install -o root -g root -m 0750 -d /root/.unison |
|||
* Shutdown DC2 Samba AD DC |
|||
cat << EOF > /root/.unison/default.prf |
|||
mv /var/lib/samba/private/idmap.ldb /var/lib/samba/private/idmap.ldb.backup" |
|||
# Unison preferences file |
|||
rm /var/cache/samba/gencache.tdb" |
|||
# Roots of the synchronization |
|||
# |
|||
# copymax & maxthreads params were set to 1 for easier troubleshooting. |
|||
# Have to experiment to see if they can be increased again. |
|||
root = /var/lib/samba |
|||
# Note that 2 x / behind DC2, it is required |
|||
root = ssh://root@DC2//var/lib/samba |
|||
# |
|||
# Paths to synchronize |
|||
path = sysvol |
|||
# |
|||
#ignore = Path stats ## ignores /var/www/stats |
|||
auto=true |
|||
batch=true |
|||
perms=0 |
|||
rsync=true |
|||
maxthreads=1 |
|||
retry=3 |
|||
confirmbigdeletes=false |
|||
servercmd=/usr/bin/unison |
|||
copythreshold=0 |
|||
copyprog = /usr/bin/rsync -XAavz --rsh='ssh -p 22' --inplace --compress |
|||
copyprogrest = /usr/bin/rsync -XAavz --rsh='ssh -p 22' --partial --inplace --compress |
|||
copyquoterem = true |
|||
copymax = 1 |
|||
logfile = /var/log/sysvol-sync.log |
|||
EOF |
|||
=== Setup SysVol on DC2 === |
|||
* On DC2 Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs! |
|||
* On DC2 Install unison by using your package manager or compile from source. (Gentoo need to do <tt>eselect unison</tt> to create the link) |
|||
* Run the following command on '''DC1''' |
* Run the following command on '''DC1''' |
||
scp /var/lib/samba/private/idmap.ldb root@DC2:/var/lib/samba/private/ |
|||
ssh DC2 "cp -R --preserve=all /var/lib/samba/sysvol /var/lib/samba/" |
|||
== 1st Try == |
|||
== 1st Trial == |
|||
What happen is we use rsync to create the directory structure with extended attributes |
What happen is we use rsync to create the directory structure with extended attributes |
||
Than unison setup copies only the extened attributes on files. |
Than unison setup copies only the extened attributes on files. |
||
<BR>Please make a '''backup''' on you sysvol just in case |
<BR>Please make a '''backup''' on you sysvol just in case as we are really '''TRYING''' there are no <tt>dry-run</tt> |
||
/usr/bin/rsync -XAavz --log-file /var/log/sysvol-sync.log --delete-after -f"+ */" -f"- *" /var/lib/samba/sysvol root@DC2:/var/lib/samba && /usr/bin/unison &> /dev/null |
|||
:'''Note: The path on DC2 are just /var/lib/samba which is different from DC1, it is by design, there is nothing wrong!''' |
|||
/usr/bin/osync.sh /etc/osync/sync.conf --dry --verbose |
|||
If this run successfully let remove the --dry and execute it. |
|||
/usr/bin/osync.sh /etc/osync/sync.conf --verbose |
|||
== Add to Crontab on DC1 == |
== Add to Crontab on DC1 == |
||
On DC1 run the following: |
On DC1 run the following: |
||
crontab -e |
crontab -e |
||
*/5 * * * * root /usr/bin/ |
*/5 * * * * root /usr/bin/rsync -XAavz --log-file /var/log/sysvol-sync.log --delete-after -f"+ */" -f"- *" /var/lib/samba/sysvol root@DC2:/var/lib/samba && /usr/bin/unison &> /dev/null |
||
:'''Warning: Make sure that the destination folder is really your SysVol folder, because the command will replicate to the given directory and sync everything in it that isn't also on the source! You could damage your system! So check the output carefully if the replication is doing, what you expect!''' |
:'''Warning: Make sure that the destination folder is really your SysVol folder, because the command will replicate to the given directory and sync everything in it that isn't also on the source! You could damage your system! So check the output carefully if the replication is doing, what you expect!''' |
||
Line 110: | Line 118: | ||
:'''Warning: Please follow the steps below OR you can end up with an empty sysvol folder.''' |
:'''Warning: Please follow the steps below OR you can end up with an empty sysvol folder.''' |
||
# Disable Cron on DC1, like Add a "#" on the line with <tt>crontab -e</tt> |
# Disable Cron on DC1, like Add a "#" on the line with <tt>crontab -e</tt> |
||
# Check is any rsync or |
# Check is any rsync or unison are currently running in <tt>ps -aux</tt> if yes, wait for it to finished OR kill it (if it is zombie) |
||
# Remove the |
# Remove the hash files on both DC1 and DC2 on <tt>/root/.unison</tt> |
||
# Now check your sysvol and resync |
# Now check your sysvol and resync |
||
# Confirm that everything is ok again |
# Confirm that everything is ok again |
||
Line 123: | Line 131: | ||
* What to do if I've more than one DC? |
* What to do if I've more than one DC? |
||
** |
** In Theory, We would just make more cron jobs on DC1 and the complete sync will be perform next sync to all server. |
||
* Why can't I simply use a distributed filesystem like GlusterFS, Lustre, etc. for SysVol? |
* Why can't I simply use a distributed filesystem like GlusterFS, Lustre, etc. for SysVol? |
||
** A cluster file system with Samba requires CTDB to be able to do it safely. And CTDB and AD DC are incompatible |
** A cluster file system with Samba requires CTDB to be able to do it safely. And CTDB and AD DC are incompatible. |
||
---- |
|||
[[Category:Active Directory]] |
Revision as of 21:24, 26 February 2017
Introduction
Samba AD currently doesn't provide support for SysVol replication. To achive this important feature in a Multi-DC environment, until it's implemented, workarounds are necessary to keep it in sync. This HowTo provides a basic workaround solution based on rsync and unison.
Information on unison + rsync replication
This HowTo describes a solution for SysVol replication, that is based on rsync and unison. As Compare to the rsync method, it is bidirectional. But this howto only cover two DC setup.
It have the following advantages:
- setup is fast done
- configuration is very easy
- Can work with windows (Please add in)
We will use rsync through a SSH tunnel.
Setup the SysVol replication
Some assumptions:
You are running all commands as root. rsync is located /usr/bin/rsync sysvol is located /var/lib/samba/sysvol on both DC1 and DC2 unison is located /usr/bin/unison DC1 is at DC1 DC2 is at DC2 sysvolsync log is located /var/log/sysvol-sync.log
Change the path if that don't fit your setup.
Setup on the Domain Controller with the PDC Emulator FSMO role
- Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs!
- We don't need to setup rsync server.
- Install unison by using your package manager or compile from source. (Gentoo need to do eselect unison to create the link)
Creating SSH Public Key and ssh-copy to DC2
ssh-keygen -t rsa ssh-copy-id -i ~/.ssh/id_rsa.pub root@DC2
You can try to access DC2 via ssh
ssh DC2
Setup ssh Control
If the remote system enforces rate limits on incoming ssh connections, unison wil fail if you try to run it this way. So we create the first ssh connection as a controlpath file in the location specified, all subsequent connections will reuse on the first connection.
mkdir ~/.ssh/ctl cat << EOF > ~/.ssh/ctl/config Host * ControlMaster auto ControlPath ~/.ssh/ctl/%h_%p_%r ControlPersist 1 EOF
Setup Sysvolsync Log files
Do the following on DC1 so that we can check what happen on the sync. Please include this files into to log rotate as we didn't control the log size here.
touch /var/log/sysvol-sync.log chmod 640 /var/log/sysvol-sync.log
Setup Unison defaults running parameters
Please run the following on DC1
install -o root -g root -m 0750 -d /root/.unison cat << EOF > /root/.unison/default.prf # Unison preferences file # Roots of the synchronization # # copymax & maxthreads params were set to 1 for easier troubleshooting. # Have to experiment to see if they can be increased again. root = /var/lib/samba # Note that 2 x / behind DC2, it is required root = ssh://root@DC2//var/lib/samba # # Paths to synchronize path = sysvol # #ignore = Path stats ## ignores /var/www/stats auto=true batch=true perms=0 rsync=true maxthreads=1 retry=3 confirmbigdeletes=false servercmd=/usr/bin/unison copythreshold=0 copyprog = /usr/bin/rsync -XAavz --rsh='ssh -p 22' --inplace --compress copyprogrest = /usr/bin/rsync -XAavz --rsh='ssh -p 22' --partial --inplace --compress copyquoterem = true copymax = 1 logfile = /var/log/sysvol-sync.log EOF
Setup SysVol on DC2
- On DC2 Install rsync by using your package manager or compile from source. Make sure, that you use a version that supports extended ACLs!
- On DC2 Install unison by using your package manager or compile from source. (Gentoo need to do eselect unison to create the link)
- Run the following command on DC1
ssh DC2 "cp -R --preserve=all /var/lib/samba/sysvol /var/lib/samba/"
1st Trial
What happen is we use rsync to create the directory structure with extended attributes Than unison setup copies only the extened attributes on files.
Please make a backup on you sysvol just in case as we are really TRYING there are no dry-run
/usr/bin/rsync -XAavz --log-file /var/log/sysvol-sync.log --delete-after -f"+ */" -f"- *" /var/lib/samba/sysvol root@DC2:/var/lib/samba && /usr/bin/unison &> /dev/null
- Note: The path on DC2 are just /var/lib/samba which is different from DC1, it is by design, there is nothing wrong!
Add to Crontab on DC1
On DC1 run the following:
crontab -e */5 * * * * root /usr/bin/rsync -XAavz --log-file /var/log/sysvol-sync.log --delete-after -f"+ */" -f"- *" /var/lib/samba/sysvol root@DC2:/var/lib/samba && /usr/bin/unison &> /dev/null
- Warning: Make sure that the destination folder is really your SysVol folder, because the command will replicate to the given directory and sync everything in it that isn't also on the source! You could damage your system! So check the output carefully if the replication is doing, what you expect!
When you try to resync the folder
- Warning: Please follow the steps below OR you can end up with an empty sysvol folder.
- Disable Cron on DC1, like Add a "#" on the line with crontab -e
- Check is any rsync or unison are currently running in ps -aux if yes, wait for it to finished OR kill it (if it is zombie)
- Remove the hash files on both DC1 and DC2 on /root/.unison
- Now check your sysvol and resync
- Confirm that everything is ok again
- Re-enable the Cron on DC1 again
FAQ
- How can I do this on windows?
- I don't have an answer, please post on the mailing list
- What to do if I've more than one DC?
- In Theory, We would just make more cron jobs on DC1 and the complete sync will be perform next sync to all server.
- Why can't I simply use a distributed filesystem like GlusterFS, Lustre, etc. for SysVol?
- A cluster file system with Samba requires CTDB to be able to do it safely. And CTDB and AD DC are incompatible.