Basic CTDB configuration

From SambaWiki
Revision as of 10:12, 26 October 2016 by MartinSchwenke (talk | contribs) (Created page with "= Goal = Set up a cluster of nodes, each running CTDB. The cluster will not be useful. In particular: * Samba will not be managed by CTDB * There will be no CTDB public IP...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)


Set up a cluster of nodes, each running CTDB.

The cluster will not be useful. In particular:

  • Samba will not be managed by CTDB
  • There will be no CTDB public IP addresses configured
  • There will be no CTDB recovery lock configured

However, all useful configurations are extensions of a default configuration, so it is important to test this first.

CTDB Cluster Configuration

CTDB configuration directory

CTDB's configuration files are stored in /etc/ctdb/. They may be stored somewhere else, such as /usr/local/etc/ctdb/, depending on how CTDB was installed. However, for simplicity and brevity, this guide will use /etc/ctdb/.

ctdbd configuration file

The preferred file for CTDB daemon configuration is ctdbd.conf (in the CTDB configuration directory). Linux distribution-specific configuration files such as /etc/sysconfig/ctdb or /etc/default/ctdb are also supported. Depending on how CTDB was installed, a template configuration file may be installed.

There are many configuration variables that can be set in the ctdbd configuration file. Please see ctdbd.conf(5) for details.

However, for the most basic configuration, the ctdbd configuration file should be empty or have all lines commented out. This results in a default configuration.

nodes file

The configuration variable used to specify the nodes file is CTDB_NODES. When this variable is not set then the nodes file (in the CTDB configuration directory) is used.

This file contains a list of the private IP addresses that the CTDB daemons will use in your cluster. This should be a private non-routeable subnet which is only used for internal cluster traffic.


Note that the order of addresses in this file is significant. Lines commented with '#' are also significant.

This file must be the same on all nodes in the cluster.

Starting the cluster

This will depend on how CTDB was installed. If installing from source, consider installing the provided init script (ctdb/config/ctdb.init) or system service file (ctdb/config/ctdb.system) in the appropriate place. A binary package should already contain the correct method of starting CTDB.

CTDB's onnode command is a useful way of running a command on all configured nodes. Depending on your installation, you may be able to start CTDB on all nodes by running something like:

 onnode -p all service ctdb start

Checking cluster status

ctdb is a command for interacting with ctdbd. Its uses include control and status. See ctdbd.conf(1) for details.

ctdb status

The ctdb status command provides basic information about the cluster and the status of the nodes. Output looks like:

 Number of nodes:4
 vnn:0       OK (THIS NODE)
 vnn:1       OK
 vnn:2       OK
 vnn:3       OK
 hash:0 lmaster:0
 hash:1 lmaster:1
 hash:2 lmaster:2
 hash:3 lmaster:3
 Recovery mode:NORMAL (0)
 Recovery master:0

The important parts are in bold:

  • All 4 nodes are in a healthy state
  • Recovery mode is NORMAL, which means that the cluster has completed a recovery and is running in a normal fully operational state

Recovery state will briefly change to RECOVERY when there has been a node failure or something is wrong with the cluster.

If the cluster remains in RECOVERY state for very long (many seconds) there might be a configuration problem. Check the logs for details.

ctdb ping

The ctdb ping command ensures the local CTDB daemon is running and shows how many clients are connected.

 # onnode -q all ctdb ping
 response from 0 time=0.000050 sec  (2 clients)
 response from 1 time=0.000154 sec  (2 clients)
 response from 2 time=0.000114 sec  (2 clients)
 response from 3 time=0.000115 sec  (2 clients)

The 2 clients in question here are the ctdb command and CTDB's recovery daemon. In more complex configurations, where Samba is running, there may be many more clients.

That's it!

If the cluster status looks good then CTDB can be configured to do useful things.

If not, then check the logs - something like /var/log/log.ctdb by default.